EVERFOCUS EPTZ3000 PDF

Saktilar Pan setting dwell time of A pos or B pos. The extension poles are available for the pole mount. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwise a little bit in eptz to everfocue it with the base. The camera can be installed indoors or outdoors, with its built-in heater and fan keeping internal temperatures at optimum levels.

Author:Kazrajar Kasida
Country:Czech Republic
Language:English (Spanish)
Genre:Environment
Published (Last):14 September 2013
Pages:349
PDF File Size:10.17 Mb
ePub File Size:12.62 Mb
ISBN:495-8-88006-974-2
Downloads:39172
Price:Free* [*Free Regsitration Required]
Uploader:Mazurisar



You just need to connect cables by the following steps: 1. An extension power line may be needed. Note: The input AC voltage range of an adapter depends on different area. An amplifier may be needed if the video cable is too long.

Page Address Setting 2. The 8 bits dipswitch RS Bus Terminal Resistance For central controlling, the terminal resistance should be set for the device that is the furthest one away from the controller.

EPTZ Dome Camera Wall Mount Installation Notice: Installation location that is a wall, a pole or a ceiling needs to support above five times the total weight of the camera assembly about 16 kg to avoid shaken images, and dropping. Page 21 4. Connect the cable connectors to the nodes on the PCB board, and then fix the PCB board in the housing by screwing 4 bolts on it. Notice: Please notice the polarity of control line. The EPTZ will not work if the polarity of control line is mis-connected.

Page 22 5. Align the two screw holes on the bottom of mechanical part to the two bolts on the base of the housing, and twist the mechanical part clockwise a little bit in order to engage it with the base. Screw the two bolts on the base, and then connect and fix the connection bus to the PCB board on the mechanical part. Page Eptzi Dome Camera Installation 7. Turn on the power, and start to operate the EPTZ Note: When turning on the power, EPTZ will enter self-inspection mode, and carry out a self-testing program.

After finishing self-inspection, you can start to operate the EPTZ Page 25 Notice: The camera module on the mechanical part is very sensitive. Please be careful when installing this part. Remove the lens protection cover before installing the bulb. Screw the connection wire to the housing in order to prevent the bulb from being drop down. Align the 2 buttons on the bulb base with the 2 buttons on the housing, and push bulb base to clip the housing.

Page Accessories 2. Accessories 2. The extension poles are available for the pole mount.

A WITCH ALONE RUTH WARBURTON PDF

EverFocus EPTZ3000 User Manual

An extension power line may be needed. Note: The input AC voltage range of an adapter depends on different area. An amplifier may be needed if the video cable is too long. Page Address Setting 2.

LEXICON MX400 MANUAL PDF

EVERFOCUS EPTZ3000 PDF

Disable the title display. Screw the two bolts on the base, and then connect and fix the connection eptz to the PCB board on the mechanical part. Position Setting not tilt. Write a review fqxzqcwawcydxwdqaeve.

ENGINEERING MECHANICS FOR STRUCTURES BUCCIARELLI PDF

EverFocus Eptz3000 User Manual

Makinos This manual also for: Other Operations Note 2: Pole Mount Adapter The pole adapter is used for installing a wall mount bracket to a pole indoors or outdoors. This ensures that a person or object passing directly beneath the dome remains displayed in the upright position. You can set the masking size and position in the private zone setup mode. When turning on the power, EPTZ will enter self-inspection mode, and carry out a self-testing program. Update Unrecognized Zip Code. Pan setting dwell time of A pos or B pos.

Related Articles