ADCOR 500S PDF

When fully encapsulated by poured concrete, the expansive forces form a seal against concrete faces. This seal resists hydrostatic pressure, and is specifically engineered to stop water from entering sub-structures. Applications Construction joints in in-situ concrete structures Casting new concrete against existing Floor slabs cast against diaphragm retaining walls, steel sheet piles and secant piled walls Joints between floor slabs and pile caps Pipe penetrations through floors and walls Product Advantages Controlled volumetric expansion reduces risk of concrete spalling Retains cohesive strength at both original and expanded volume Malleable and conformable, enabling easy application to a variety of concrete profiles and a variety of irregular substrates Resists at least ft. Not suitable for use with pre-cast concrete components. Mechanical fasteners should never be used as the only means of securement.

Author:Zuzil Yozshujora
Country:Puerto Rico
Language:English (Spanish)
Genre:Education
Published (Last):26 February 2007
Pages:70
PDF File Size:6.55 Mb
ePub File Size:2.80 Mb
ISBN:192-1-94505-552-2
Downloads:25474
Price:Free* [*Free Regsitration Required]
Uploader:Faegrel



When fully encapsulated by poured concrete, the expansive forces form a seal against concrete faces. The seal resists hydrostatic pressure, stopping water from entering sub-structures. Superior performance arises from: Controlled, reproducible, volumetric expansion. Cohesive strength maintained after volumetric expansion.

Malleable and plastic, enabling easy application to a variety of concrete profiles. Adcor Mastic A hydrophilic mastic for use as a bedding bead on irregular concrete surfaces prior to the application of Adcor S. Adcor Mastic can also be used as a stand alone hydrophilic sealant where application of Adcor S is impractical. Supplied in cartridges for gun application. Supplied in cans for brush application. Details shown are typical illustrations only and not working drawings. Not suitable for use with pre-cast concrete components.

Design Waterstop networks must be continuous through all joints and penetrations if they are to be effective. Adcor S can be easily jointed to these profiles see detail. Installation Concrete surfaces must be clean and free of all contaminants.

Remove all concrete spatter and nibs. On irregular concrete faces gun a 10mm bead of Adcor Mastic as a bedding for Adcor S. Fix Adcor S using masonry nails 40mm to 50mm long with a washer 20mm in diameter. Hilti EM FP8 shot fired fixings with 6mm nuts and 20mm diameter washers may also be used.

Fixings should be spaced at a maximum of mm centres. Adcor Adhesive MS can be used on clean substrates, wire brushed to remove all dust, dirt, rust and other contaminants. The adhesive is damp surface tolerant but will not adhere to wet surfaces.

Gun a 10mm bead onto the substrate, and press Adcor S firmly into place. Pak Adhesive must be applied to dry substrates only. Apply by brush to both the substrate and Adcor S. Wait until both surfaces are dry to touch, then press Adcor S firmly into place. All joints should be overlapped mm. Ensure full contact between jointed pieces. Adcor S can be bent around corner. However on complex geometry use Adcor Mastic as a gap filler. Any damaged sections should be removed and repaired with either a new section of Adcor S or a 25mm min bead of Adcor Mastic.

Keep Adcor S dry prior to pouring concrete. Product Advantages Controlled volumetric expansion - reduces risk of concrete spalling. Conformable — can be installed onto a variety of irregular substrates.

Retains cohesive strength at both original and expanded volume. No need for protective steel mesh. Resists at least 6 bar 60m hydrostatic pressure. Simple overlap jointing on site. Reproducible swell after wet — dry cycling. Contains no sodium bentonite. Can be easily joined to PVC waterstops at movement joints.

INGO SWANN DATABASE PDF

Adcor® 500S

Not suitable for use with pre-cast concrete components. Design Waterstop networks must be continuous through all joints and penetrations if they are to be effective. Installation Concrete surfaces must be clean and free of all contaminants. Remove all concrete spatter and nibs. Hilti EM6- FP8 shot fired fixings with 6 mm nuts and 20 mm diameter washers may also be used. Fixings should be spaced at a maximum of mm centres.

DEMOLISHING STRONGHOLDS PDF

ADCOR® Hydrophilic Waterstop

.

DISCINESIA CILIAR PRIMARIA PDF

ADCOR® 500S Waterstop

.

ITEXTSHARP XMLWORKER HTML TO PDF

Adcor 500 S 5m

.

Related Articles